![]() If you only have a jigsaw available, however, just cut slowly and do the job right the first time. Most people find that using a circular saw is the best choice. It is going to take more concentration and focus on your part to ensure that each cut is done appropriately.Ĭopyright protected content owner: and was 1st posted on. When using a jigsaw for cutting vinyl lattice, you switch from cutting the entire piece to cutting each individual piece within it. It also does a good job of cutting a straight cut, but you should use a straight edge to guide the jigsaw when doing so. Jigsaws are commonly used for cutting vinyl lattice and other materials when odd shapes need to be cut. Keep that in mind and use a large pair of snips if you have them available. Obviously, thicker material is going to be more difficult to cut. If you are using a top-grade vinyl lattice, it may be too thick for most snips to handle. Snips are better used for thin materials as well. Tin snips can be used to cut vinyl lattice but you need to use a heavy-duty set if you want them to cut properly. ![]() Can You Use Tin Snips To Cut Vinyl Lattice? Keep a good grip on the saw and beware of the possibility of kickback. You should also be cautious when using a circular saw because things can go wrong quickly. If you notice that the blade is getting gummy from the vinyl melting, switch to a new blade. As you are cutting the lattice, work slowly so you don’t chip the forward edge as you are cutting.Ī circular saw will cut through the vinyl easily but you must ensure that you are using a sharp blade. Use a carbide-tipped blade with fine teeth to cut through it quickly and easily. ![]() Can You Use Circular Saw To Cut Vinyl Lattice?Ī circular saw is the best choice for cutting vinyl lattice. You can then cut through it with a handsaw and get the job done. This can be difficult when working with vinyl lattice, because you must stabilize the individual slats as well as the entire piece.Įither use a portable bench or sawhorses for stabilizing the vinyl lattice. When using a handsaw, make sure that you have the work stabilized. Many people find that using a handsaw is beneficial because it gives you additional control over the cut you are making. If you have a handsaw that is suitable for cutting through wood, it will likely cut through vinyl lattice just as easily. Can You Use Hand Saw To Cut Vinyl Lattice? Let’s consider some of the different tools that may be used for cutting this material. The more you protect yourself and work safely, the more likely it is that you will finish the job with all your fingers and toes intact. Other important safety reminders include wearing all-purpose gloves and hearing protection. When cutting most pieces of wood, safety glasses will suffice but you are likely to have flying pieces if something goes astray when cutting lattice. You should also wear safety glasses or preferably, a face shield over safety glasses. If the blade is dull, it will not cut as easily and it is more likely to cut you. Perhaps the most important factor for cutting vinyl lattice safely is to use a sharp blade. It is especially true of vinyl lattice, because it is similar to cutting multiple pieces rather than a single piece. Something else to keep in mind is your personal safety, which should always be at the forefront when cutting anything with a power saw. Using a fine blade that is carbide-tipped will help to avoid the problem, but if you work slowly, it is less likely to occur as well. One of the biggest issues is blowing out the lattice when you come to the second edge. As you are cutting through the small pieces of lattice, it can be easy for things to get away from you and for damage to occur. Regardless of what tool you use, it’s important to allow the tool to do the majority of the job. We will also consider some tools that you should avoid using. In this article, we will consider many different tools that can be used for the purpose of cutting vinyl lattice. Since you’re cutting through many small pieces, a straight cut is typically going to suffice. In addition, it is not typically necessary to cut odd shapes when cutting through vinyl lattice. It is portable and very convenient for doing the job. If you had to pick one particular tool that would cut vinyl lattice, it would likely be a circular saw. That will cut through the lattice, leaving you with a nice edge. Generally speaking, you should choose a fine-toothed saw blade that is carbide-tipped. You can cut through vinyl lattice with any type of saw that can be used for cutting through wood. What do you do if you have something unusual to cut, such as vinyl lattice? Most of us are accustomed to cutting standard boards, such as two-by-fours or sheets of plywood.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |